NOTICE OF INTENT TO SOLE SOURCE 70Z08526Q260000223 The Department of Homeland Security {DHS}, United States Coast Guard {USCG} Surface Forces Logistics Center {SFLC}, located at 1 Eagle Road Bldg. 55, Alameda CA 94501 is issuing this Notice of Intent {NOI} to inform industry contractors of the Government's intent to Award a Sole Source Firm Fixed Price {FFP} Contract IAW Federal Acquisition Regulation {FAR} Part 12 and 13 procedures. The intended Contractor PHILAELPHIA GEAR., located at 12935 Imperial HWY Santa Fe Springs, CA 90670 United States. USCG SFLC requires: CGC KUKUI’S Reduction gear inspection. This procurement is being conducted using commercial item procedures pursuant to Federal Acquisition Regulation {FAR} Part 12 and FAR Part 13, specifically FAR 13.106-1{b}{1}, allowing the Contracting Officer {KO} to solicit from one source. The North American Industry Classification System {NAICS} for this requirement is 336611 - Ship Building and Repairing. The Product of Service Code for this requirement is J020. This will not be a small business under the Small Business Administration {SBA} size standard for this sector. This notice of intent is neither a formal solicitation nor a request for competitive proposals. No solicitation document is available, and telephone requests will not be honored. No award will be made on the basis of unsolicited quotations or offers received in response to this notice. Any response to this notice must show clear, compelling and convincing evidence that competition will be advantageous to the Government. The intent of this synopsis is for informational purposes only. Information received will normally be considered solely for the purpose of determining whether to conduct competitive procurement. A determination by the Government not to compete this action based on this notice is solely within the discretion of the Government. All inquiries and concerns must be addressed in writing via e-mail to Ms. Oneal at
[email protected] with the following information referenced in the subject line, Solicitation 70Z08526Q260000223. A determination by the Government not to compete this proposed procurement based on the responses to this notice is solely within the discretion of the Government. Information received will be considered solely for the purpose of determining whether to conduct competitive procurement. All interested parties who are responsible, certified, and capable may identify their interest and may submit an offer or quotation which shall be considered by the agency no later than 8:00 AM Pacific Time {PST} on NOV 06, 2025, to Ms. Oneal at
[email protected] The interested parties bear full responsibility to ensure complete transmission and timely receipt. SOW USCG KUKUI Reduction Gear’s PTO-GEN Assembly Repairs (Sitka, AK) LAST UPDATED: 5/21/2025 PAGE 1/2 Shipboard Repair Services USCGC KUKUI PTO Bearing Renew 1. Background, Problem Statement: During CGC KUKUI’s Main Reduction Gear (MRG) inspection; PTO to low-speed gear, excessive bearing wear was found on high-speed gear bearings. 1.1 Main Reduction Gear (MRG) Info: MFR ID 96-DHCMGH-CP B Class Model Gear Unit Reduction: NSN 3020-XF-C11-6019 Input RPM 900 Output RPM 254 Gear ration 3.541:1 1.2 Background: USCG observed questionable flow from LO spray nozzles in the Generator Pinion Housing. A PG Service Rep visited the Cutter to address the spray nozzle issue. In the course of that work, damage additional damage internally was observed and documented in Condition Found Report (CFR) PG Order# 45880 dated 28Oct2025, 1.3 Work Requirement Statement: 1. In response to CFR45880 USCG has determined/concurred that Kukui does required the recommend repair actions of that report. 2. In response to report USCG concurs to the following repair actions to be performed by PG: A. Remove turning gear assembly. B. Uncoupled PTO shaft and support. C. Bearing renewal and axial clearance check. D. To correct the out of spec bearing clearance It is preferred that the turning gear adapter spigot PG p/g 50005-0202 be machined to set the axial clearance to spec using shim material. 3. In addition to above repair actions PG shall perform all work required to renew the following components (both those PG shall provide as well as the parts USCG shall provide) in the course of the repairs: Philadelphia Gear Provided Part Part # Description Comment 31000-0223 Bearing Cup Same as 01070-0322 PC 77 31000-0224 Bearing Cone Same as 01070-0322 PC 76 32300-2053 Spider Same as 01070-0322 PC 340 32000-0118 Coupling Hub Same as 01070-0322 PC 341 32300-1765 Coupling Hub Same as 01070-0322 PC 342 IR 162343-6 Machine Turning Gear 30 Oct 2025 SOW USCG KUKUI Reduction Gear’s PTO-GEN Assembly Repairs (Sitka, AK) LAST UPDATED: 5/21/2025 PAGE 2/2 Adapter P/N 50005-0202 USCG Provided Parts Part # Description Comment 31000-1796 Bearing Cup Same as 7501070-0322 PC 75 31000-1795 Bearing Cone Same as 01070-0322 PC 74 4. At conclusion of repairs perform the following tasks in conjunction/company with Cutter personnel: • grease the associated lip seals • observe proper spray patterns • perform dock trial • Final torque of Generator Housing Cover 5. Period of Performance 11 November 2025 15 December 2025 6. Location of Performance CGC KUKUI 1480 Seward Ave Sitka, AK 99835 POC: CWO2 Brandon Erler (907) 966-5470 7. Acceptance Criteria • N/A 8. Security and Confidentiality • KTR shall provide: • State Issued Identification numbers to include issuing state for all personnel • Vehicle license plate number to include issuing state for all KTR vehicles • Each vehicle year, make, and model 9. Reporting Requirements • N/A 10. Legal Compliance • KTR shall comply with all applicable Federal, State, and Local laws and regulations. 11. Performance Monitoring • N/A