This is a combined synopsis/solicitation for commercial items prepared in accordance with the format in FAR Subpart 12.6, as supplemented with additional information included in this notice. This announcement constitutes the only solicitation; proposals are being requested and a written solicitation will not be issued. (ii) Solicitation F2KBAD2151A006 is issued as a request for quotation (RFQ). (iii) This solicitation document and incorporated provisions and clauses are those in effect through Federal Acquisition Circular 2005-60, Effective 26 July 2012. (iv) This procurement is being issued as Unrestricted under NAICS code 334516, Analytical Laboratory Instrument Manufacturing; size standard 500 employees. The Government intends to award five contract line item numbers: CLIN 0001 Digital Delay / Pulse Generator 1 each Delays • Channels: 4 independent pulses controlled in position and width • Delay channels: 8 delay channels (see below for more spec's) • Delay range: 0 to 2000 s • Accuracy: 1 ns + (timebase error x delay) • Jitter (rms)-ext trigger to any output: 25 ps + (timebase jitter x delay) • Jitter (rms)-T0 to any output: 15 ps + (timebase jitter x delay) • Trigger delay: 85 ns (external trigger To T0 output) Timebases • Jitter: 10-8 s/s • Stability: 2 X 10-6 (20-30 C) • Aging: 5 ppm/yr • External input: 10 MHz +/- 10 ppm, sine > 0.5 Vpp, 1 kohm impedance • Output: 10 MHz, 2 Vpp sine into 50 Ohms External trigger • Rate: DC to 1/(100 ns + longest delay) (Maximum of 10 MHz) • Threshold: +/- 3.5 VDC • Slope: Trigger on rising or falling edge • Impedance: 1 MOhm + 15 pF Internal rate generator • Trigger modes: Continuous, line or single shot • Rate: 100 microHz to 10 MHz • Resolution: 1 microHz • Accuracy: Same as timebase • Jitter (rms): < 25 ps (10 MHz/N trigger rate) • Jitter (rms): < 100 ps (other trigger rates) Burst generator • Trigger to first T0 - range: 0 to 2000 s • Trigger to first T0 - resolution: 5 ps • Period between pulses - range: 100 ns to 42.9 s • Period between pulses - resolution: 10 ns • Delay cycles per burst: 1 to 232-1 • Outputs: (T0, AB, DC, EF, and GH) • Source impedance: 50 Ohm • Transition time: < 2ns • Overshoot: < 100 mV + 10% of pulse amplitude • Offset: +/- 2 V • Amplitude: 0.5 to 5.0 V (level + offset < 6.0 V) • Accuracy: 100 mV + 5% of pulse amplitude General • Computer interfaces: GPIB (IEEE-488.2), RS-232, and Ethernet - all instrument functions can be controlled through the interfaces • Non-volatile memory: Nine sets of instrument configurations can be stored and recalled • Power: < 100 W, 90 to 264 VAC, 47 to 63 Hz • Warranty: One year parts and labor on defects in materials and workmanship CLIN 0002 Eight delay channels 30 V 1 each • Outputs (BNC): T0, A, B, C, D, E, F, G, H • Source impedance: 50 Ohm • Transition time: < 5 ns • Levels: 0 to 30 V into high impedance • Levels: 0 to 15 V into 50 Ohm (amplitude decreases by 1%/kHz) • Pulse characteristics - rising edge: At programmed delay • Pulse characteristics - falling edge: 100 ns after the rising edge CLIN 0003 Fast rise time module that is compatible with digital delay/pulse generator 1 each • Rise time: < 100 ps • Fall time: < 3 ns • Offset: 0.8 V to 1.1 V • Amplitude: 0.5 V to 5.0 V • Load: 50 Ohms CLIN 0004 O4C- Bias Tee (for SDR1) 1 each CLIN 0005 Shipping The following provisions and clauses apply to this procurement: In accordance with the FAR 13.106-1(a)(2) offerors are notified that award will be made to the lowest price technically acceptable offeror. Offeror will be evaluated in accordance with FAR 13.106-2. FAR 52.212-3, Offeror Representations and Certification-Commercial Items (all offerors shall include a completed copy of this provision with their proposal); An offeror shall complete only paragraphs (b) of this provision if the offeror has completed the annual representations and certificates electronically at http://orca.bpn.gov. If an offeror has not completed the annual representations and certifications electronically at the ORCA website, the offeror shall complete only paragraphs (c) through (m) of this provision; FAR 52.212-4, Contract Terms and Conditions-Commercial Items; FAR 52.212-5, Contract Terms and Conditions Required to Implement Statutes or Executive Orders-Commercial Items. [in paragraphs (b) and (c) the following clauses apply 52.219-6, 52.219-28; 52.222-3; 52.219-8; 52.219-14; 52.222-21; 52.222-26; 52-222-36; 52-222-37; 52.225-13; 52.232-33; 52.222-44; Addendum to FAR 52.212-5: 52.246.4; FAR 52.252-2, Clauses and provisions may be accessed in full text at http://farsite.hill.af.mil/; 52.237-2 Protection of Government Buildings, Equipment and Vegetation; DFAR 252.212-7001 Contract Terms and Conditions Required to Implement Statutes or Executive Orders Applicable to Defense Acquisitions of Commercial Items. [in paragraph(s) (a) and (b) the following clause(s) apply [52.203-3, 252.225-7001, 252.225-7002,252.225-7012, 252.225-7021 ALT I, 252.225-7036, 252.232-7003,252.243-7002, 252.247-7023]. 52.232-18, 52.242-13, 252.225-7000, 252.247-7022, AFFARS 5352.201-9101, 5352.223-9001, AFFARS 5352.242-9000 and AFFARS 5352.201-9101,Ombudsman. All payments are to be paid via the Internet through the Wide Area Work Flow (WAWF) system. WAWF may be accessed at https://wawf.eb.mil. WAWF training may be accessed online at http://www.wawftraining.com. Payment information may be accessed using the DFAS website at https://www.dfas.mil. Your purchase order/contract number of invoice will be required to inquire status of your payment. Quotes may be E-mailed (preferred) to
[email protected] or mailed to AFNWC/PKOA, ATTN: Michael D. Camp, 2000 Wyoming Blvd SE, Bldg. 20604, Room B-22, Kirtland AFB., NM 87117, or faxed to (505) 846-4262 ATTN: Michael D. Camp. ADDITIONAL INFORMATION: Be advised that all interested parties must be registered in the SAM Database in order to receive an award. If you are not registered you may request an application at (888) 227-2423 or through the SAM website at http://SAM.gov. Specifications: See CLIN's above