THIS IS A COMBINED SYNOPSIS/SOLICITATION. This announcement constitutes the only solicitation; quotes are being requested and a written solicitation will not be issued.(i) This solicitation, N68335-07-P-0541, is issued as a competitive request for Quote (RFQ). (ii) This solicitation will be 100% small business set aside in accordance with FAR 52.219-6. The NAICS is 333991. (iii) Contract Line Item Numbers (CLINS) are as follows: CLIN0001 for a qty of four (4) Power Drive Tool. The tool will be used in lieu of an 8 inch hand crank with a half inch male square drive. The tool shall be inherently safe for use around aircraft in accordance with NFPA 70. The tool shall be compatible with all the environmental requirements of MIL-STD-810E and MIL-STD-464. The tool shall maintain system level electromagnetic compatibility in accordance with MIL-HDBK-235. The tool shall also comply with the following test specifications as directed by MIL-STD-464 including MIL-STD-461E and MIL-STD-462. The tool shall be capable of being operated by one person, and shall weigh no more than 35 lbs, and be able to be held with both hands to assist the operator. The tool shall be capable of rotating the 90 degree drive point at a rate no faster than 200 RPM with 25 ft lbs of torque. The tool shall have the ability to secure via a pin a torque limiting device provided by the Navy that connects to the half inch drive on the tool. The tool shall come with a 30 ft long shielded cable to connect with an existing battery currently in the navy inventory that supplies 144VDC. The cable shall be robust enough to be run over by a vehicle. The cable connector on the battery source is female with 144VDC on pin A, Ground on Pin C, and the possibility of supplying 24VDC on either pin B, D, or E. The cable shall be enclosed and shielded to protect against the environment. (iv) Delivery Inspection and Acceptance: Each Power Drive Tool shall be packed and shipped via best commercial practices. Delivery shall commence 120 days after contract award. FOB Destination. Each Power Drive Tool shall be shipped to the following destination: Aircraft / Weapons Support Equipment Test Team Unit 1, Bldg 1405, 22763 Saufley Rd Patuxent River, MD 20670-1622, ATTENTION: Anthony Ferraro (Code 4.8.6.11), DSN 342-5329, COM 301-342-5329, FAX 301-342-9508. Inspection and Acceptance will be conducted at Destination. (v) Contract Terms and Conditions: Contract Administration Data Section G: 5252.232-9511 Notice of Requirement for Prompt Payment. 5252.232-9513 Invoicing and Payment (WAWF) Instruction Contract Clauses Section I: 52.213-4 Terms and Conditions Simplified Acquisitions (Other Than Commercial Items) 52.232-33 Payments by Electronic Funds Transfer Central Contractor registration 52.244-6 Subcontracts for Commercial Items 52.252-6 Authorized Deviations in Clauses 252.204-7004 Alt A Central Contractor Registration Alt A 252.232-7003 Electronic Submission of Payment Request 252.211-7003 Item Identification and Valuation (vi) Quotes are due by 03:00pm EST, 19 September 2007 at the Naval Air Warfare Center Aircraft Division Lakehurst, Attn: Michael R. Sommeling, Code 25211, Hwy 547, Bldg. 562-3, Lakehurst, NJ 08733. The Government will not accept faxed quotes. You may e-mail your quote to
[email protected] or mail it to him at the following address: Naval Air Warfare Center Aircraft Division, Contracts Dept. Bldg 562-3 attn: Michael R. Sommeling, Highway 547, Lakehurst NJ 08733. (vii) Name and telephone number of individual to contact for information regarding the solicitation: Michael R. Sommeling, (732) 323-1077, e-mail:
[email protected]. This Combined Synopsis/Solicitation will NOT be posted on the NAVAIR homepage. Hard copies of this Combined Synopsis/Solicitation and Amendments will NOT be mailed to contractors.