THIS IS A PROJECT LABOR AGREEMENT (PLA) SURVEY ONLY. This is a SPECIAL NOTICE. The 772 Enterprise Sourcing Squadron is soliciting comments from the construction community addressing use of a PLA for the restoration and modernization of Jones Hall located at Keesler AFB, Mississippi. ***No proposals are being requested or accepted with this PLA notice*** Description: 772 ESS/PKA is soliciting comments from the construction community addressing the potential use of Project Labor Agreements (PLAs) for a large-scale construction project ($35 million or more) for the following: Project scope: The Design-Bid-Build (DBB) Construction to Repair Jones Hall, B6902 at Keesler AFB (KAFB), MS, the contractor will provide the Government with a complete construction and warranty for the restoration and modernization of Jones Hall. This project will encompass the following: Prepare the temporary facilities site. Perform grading, install temporary paved walk-ways, and install temporary utilities. Upon completion of the Jones Hall renovation and removal of the RLFs, restore the site to pre-construction conditions. Procure and install temporary facilities/RLFs. Remove RLFs after construction completion. Jones Hall Restoration & Modernization Repair Renovate Arnold Hall for use as a temporary facility. Existing Jones Hall FF&E will be utilized in the temporary RLF’s and at Arnold Hall transported by the government to and from the facilities. The remaining Jones Hall FF&E, not utilized in the temporary facilities, will be transported by the contractor to the recycling center on Keesler AFB for disposal. Install the RLF and furnish temporary equipment for the FAB-T Classroom, coordinate with Raytheon to move FAB-T Equipment into the RLF before construction begins, and back into Jones Hall after construction completion. The FAB-T classroom must remain operational without interruption of more than 10 continuous days during the project. Assume that 9 months is required for Raytheon to prepare for and procure all materials and equipment needed to move the FAB-T equipment from Jones Hall to the RLF. Upgrade and repair site civil work, including repair and replacement of sidewalks, walkways, and steps to meet Architectural Barriers Act (ABA) accessibility standards. Remove the existing loading dock. Restripe the parking lot to provide ABA compliant parking and ramps. Exterior Building Envelope repairs and upgrades in compliance with UFC 4-010-01 DoD Minimum Antiterrorism Standards for Buildings. Construct structural upgrades to include helical piers, structural improvements for window framing, new shear walls, for new SSMR and hurricane shelter. Hurricane Shelter upgrades meeting ICC 500 and FEMA-361 as implemented in UFC 3-301-01. Demolish interior finishes, partition walls, and Structural Interior Design (SID) elements to provide modern classroom and laboratory spaces. Jones Hall must meet the ABA accessibility standards. Replace the interior and exterior electrical distribution systems. Coordinate with the local private electrical utility company for modifications to the exterior electrical distribution systems. Replace the existing emergency generator and construct an enclosure for the new generator. Install new floor-boxes at classrooms/labs and new electrical panels serving each classroom in the corridors. Replace the entire HVAC System. Replace the plumbing piping systems and fixtures, replace the chiller. Repair and replace Fire Protection Systems to comply with UFC 3-600-01, Fire Protection Engineering . Bring life safety egress and all other aspects of the facility into compliance with UFC 3-600-01 for new facilities. Replace the non-functioning elevator and construct an enclosed elevator vestibule at each floor. Replace all telecommunications distribution systems. Install Real Property Installed Equipment (RPIE) Communications. Installation of the Non-RPIE Communications conveyances, cabling, and devices. Construct the FAB-T classrooms as secure spaces with Electronic Security Systems, including access control (ACS), intrusion detection (IDS) and CCTV. These classrooms require STC-rated walls for sound transmission mitigation and the installation of Electronic Security Systems (ESS) in this construction project. Compliance with ICD-705 is not a requirement of this project. Install all facility related controls with cybersecurity measures required by UFC 4-010-06, Cybersecurity for Facility-Related Controls. Abate or remediate Asbestos Containing Materials (ACM), Lead Based Paint (LBP) and mold. Contract duration is estimated to be 24 months. A PLA is defined as a pre-hire collective bargaining agreement with one or more labor organizations that establishes the terms and conditions of employment for a specific construction project and is an agreement described in 29 U.S.C. 158(f). Federal Acquisition Regulation (FAR) Policy: Project Labor Agreement (PLA) is a tool that agencies may use to promote economy and efficiency in Federal procurement. Pursuant to Executive Order 13502, agencies are encouraged to consider requiring the use of project labor agreements in connection with large-scale construction projects. An agency may, if appropriate, require that every contractor and subcontractor engaged in construction on the project agree, for that project, to negotiate or become a party to a project labor agreement with one or more labor organizations if the agency decides that the use of project labor agreements will: Advance the Federal Governments interest in achieving economic and efficiency in Federal procurement, producing labor-management stability, and ensuring compliance with laws and regulations governing safety and health, equal employment opportunity, labor and employment standards, and other matters; and be consistent with law. References: Provision: 52.222-33 Notice of Requirement for Project Labor Agreement Clause: 52.222-34 Project Labor Agreement. In consideration of the above factors, and any others which may be deemed appropriate, the construction community is invited to comment on the use of PLAs. Of particular interest to the Government are responses to the following questions: Do you have knowledge that a PLA has been used in the local area on projects of this kind? If so, please provide supporting documentation. Are you aware of skilled labor shortages in the area for those crafts that will be needed to complete the referenced project? If so, please elaborate and provide supporting documentation where possible. Are you aware of time sensitive issues/scheduling requirements that would affect the rate at which the referenced project should be completed? If so, please elaborate and provide supporting documentation where possible. Identify specific reasons why or how you believe a PLA would advance the Federal Government’s interest in achieving economy and efficiency in Federal procurement. Identify specific reasons why you do not believe a PLA would advance the Federal Government’s interest in achieving economy and efficiency in Federal procurement. Identify any additional information you believe should be considered on the use of a PLA on the referenced project. Identify any additional information you believe should be considered on the non-use of a PLA on the referenced project. What are the likely cost impacts, if any, to your bid/proposal price if a PLA requirement is included in the solicitation? Please provide as much detail as possible regarding any anticipated cost impacts (positive or negative) of the inclusion of a PLA requirement, including any information you can provide about the magnitude of the anticipated impact. Please select one of the following: My company will not submit a proposal if PLA is required but is interested in proposing if a PLA is not a requirement. My company plans to submit a proposal whether PLA is required or not. My company only plans to submit a proposal if PLA is required. In addition to affirmative responses, we are seeking negative responses to identify any potential actions we may take to improve the competitive environment. Please provide a response with feedback including rationale for not wanting to submit a proposal and any recommendations that could promote interest. Please provide your comments to the Contracting Officer, Samuel L. Mendez II (
[email protected]) and Contract Specialist , Dalam R. Siewert (
[email protected]) no later than 2:00 PM Central Standard Time on 13 February 2026.