CGC STEADFAST DRYDOCK FY14

The United States Coast Guard Surface Forces Logistics Center, Norfolk, VA intends to issue a Commercial Request for Quotation (RFQ) for the Drydock Repairs to USCGC STEADFAST (WMEC-623), a 210 Foot "B Class" Medium Endurance Cutter. The NAICS Code is 336611. The Coast Guard intends to conduct this procurement in accordance with Federal Acquisition Regulation (FAR) Part 12, Acquisition of Commercial Items and FAR Subpart 13.5, Test Program for Certain Commercial Items. This procurement will be issued as a Total Small Business set-aside. The solicitation will be issued electronically via the Federal Business Opportunities (FEDBIZOPPS) web page at http://www.fbo.gov on or about 17 March 2014. It is incumbent upon contractors to monitor the FEDBIZOPPS web page for the RFQ release and all subsequent amendments. Hard copies of the specification and solicitation will not be issued. This commercial item requirement is set-aside for Total Small Business Concern and will be evaluated where Past Performance is more important than Price. The home pier of the vessel is located at 17th Street Pier, Astoria, OR 97103. All work will be performed at the contractor's facility. This vessel is geographically restricted to a facility located within 300 road miles of cutter's permanent berth. The period of performance is fifty-six (56) calendar days scheduled to begin on or about 07 May 2014 and end on or about 02 July 2014. The contractor shall provide all labor, material and equipment necessary for drydock repairs to the USCGC STEADFAST (WMEC-623 ). The scope of the acquisition is for the overhauling, cleaning, repairing, testing, and inspecting of various items aboard the USCGC STEADFAST (WMEC-623). This work will include, but is not limited to: WORK ITEM 1: Hull Plating (U/W Body), Ultrasonic Testing WORK ITEM 2: Appendages (U/W), Leak Test WORK ITEM 3: Appendages (U/W) - Internal, Preserve WORK ITEM 4: Voids (Non-Accessible), Leak Test WORK ITEM 5: Voids (Non-Accessible), Preserve Internal Surfaces WORK ITEM 6: Propulsion Shaft, Renew WORK ITEM 7: Propulsion Shaft Coating, Renew WORK ITEM 8: Propulsion Shaft Seal (Mechanical and Inflatable) Assemblies, Overhaul or Renew WORK ITEM 9: Propulsion Shafting, Optical or Laser Alignment Check WORK ITEM 10: Propulsion Stern Tube Bearings, Renew WORK ITEM 11: Controllable Pitch Propeller (CPP) Oil Distribution (OD) Box, Inspect, Service & Piping Renewal WORK ITEM 12: Fathometer Transducer, Renew WORK ITEM 13: Underwater (Speed) Log Transducer, Renew WORK ITEM 14: Sea Valves and Waster Pieces, Overhaul or Renew WORK ITEM 15: Sea Strainers - Duplex (All Sizes), Overhaul WORK ITEM 16: Rudder Assembly; Remove, Inspect and Reinstall WORK ITEM 17: Rudder(s), Preserve ("100%") WORK ITEM 18: Rudder Stock Bearings Clearances, Check WORK ITEM 19: Tanks (MP Fuel Service), Preserve "100%" WORK ITEM 20: Tanks (Potable Water), Preserve "Partial" WORK ITEM 21: U/W Body, Preserve (100%) WORK ITEM 22: Hull Plating Freeboard, Preserve - Partial WORK ITEM 23: Cathodic Protection / Zinc Anodes, Renew WORK ITEM 24: Drydocking WORK ITEM 25: Temporary Services, Provide WORK ITEM 26: Ventilation Fans (Venaxial), Overhaul WORK ITEM 27: Handrails and Stanchions, Renew WORK ITEM 28: Hydraulic Power Unit Hydraulic Tank, Preserve WORK ITEM 29: Piping Insulation, Renew WORK ITEM 30: Propulsion Shaft Fairwaters and Rope Guards, Inspect and Repair WORK ITEM 31: Propulsion Shaft Bearings (External), Renew WORK ITEM 32: Controllable Pitch Propeller (CPP) System, Service WORK ITEM 33: Propeller Blades, Inspect WORK ITEM 34: Fire Pump Motors, Renewal WORK ITEM 35: Piping, Renew WORK ITEM 36: Casualty Power Cable Rack, Install WORK ITEM 37: Oily Water Holding Tank, Renew Plate WORK ITEM 38: JP5 Transfer Pump Foundation and Service Pump Foundation, Retarget WORK ITEM 39: Mast Halyard Staple, Renewal WORK ITEM 40: Propulsion Shafting, Strain Gage Alignment Inspections WORK ITEM 41: Superstructure, Preserve "Partial" WORK ITEM 42: 28 Volt DC Helo Power Supply, Load Test WORK ITEM 43: 400 Hz Power Supply (FCX Systems Inc.), Load Test WORK ITEM 44: Windspeed Transmitter (Anemometer), Renew WORK ITEM 45: Helo Talon Grids, Inspect and Test ("B-Class") WORK ITEM 46: Watertight Hatch Internal, Renew A CD-ROM containing all applicable drawings will be sent via U.S. Mail to contractors upon request. Send all drawing requests to [email protected]. The CD-ROM(s) contain WINDOWS compliant raster/vector formats (e.g.*.DWF, etc) For information concerning this acquisition, contact Mable Lee at (757) 628-4820 or by e-mail at [email protected].