This is a SOURCES SOUGHT NOTICE ONLY. It is neither a solicitation nor a request for quote (RFQ) and it does not obligate the Government to award a contract. Request for solicitation will not receive a response. The Government will not pay nor reimburse any costs of preparing this response. The source s sought notice is for market research purposes to make the appropriate acquisition decision and gain knowledge of potential qualified businesses and their Small Business Administration (SBA) size classification in relation to North America Industry Classification System (NAICS) 335132, Commercial, Industrial and Institutional Electric Lighting Fixture Manufacturing with an associated size standard of 600 employees. The Department of Veterans Affairs (VA), Network Contracting Office (NCO) 8 Orlando Contracting Team is seeking interested sources for Bollard Lighting for the Orlando VA Medical Center (OVAMC). See attached documentation to see the salient characteristics. If your business can meet or exceed the requirement, please provide a capability statement. The capability statement shall be limited to no more than five pages and must clearly state the following: Capability in industry to manufacture or provide the required Bollard Lighting. Offerors who cannot provide historical information from their company regarding the outlined attachment or similar scope and scale should provide corresponding information to show how the company would meet the OVAMC requirements. This information should provide level of confidence in the Government that an offeror would meet or exceed the delivery requirements to provide the required product. Salient Technical Characteristics for the Outdoor LED Bollard One-piece sand-cast aluminum housing with minimum 1/2 inch (0.5 ) thick walls throughout for high-impact and vandal resistance in high-traffic outdoor applications Nautically or coastally inspired curved/rounded aesthetic profile with seamless, wave-like or hydrodynamic form factor for pedestrian-scale architectural integration Nominal LED array wattage of 18W (array input approximately 18.2W), with total system input power not exceeding 20.4W, capable of replacing up to 70W metal halide or high-pressure sodium HID equivalents Delivered lumens in the range of 1,800 to 2,420 (targeting the higher end for this wattage class), with selectable correlated color temperatures of 3000K, 4000K, or 5000K IESNA Type III light distribution: medium-wide asymmetric forward throw optimized for uniform pedestrian pathway, walkway, and parking area illumination; extended forward reach with controlled side spill, minimal backlight, and soft edge transitions to eliminate hotspots Full-cutoff optical design with zero uplight (U=0 BUG rating compliant), sharp horizontal cutoff to minimize glare and ensure dark-sky/fixture shielding compliance Vandal-resistant, clear UV-stabilized polycarbonate lens fully shielding the LED light engine, providing uniform, low-brightness output with no visible diodes or direct glare Electronic universal voltage driver (120-277V, 50/60Hz), total harmonic distortion 0.90, internal surge protection minimum 2kV, and standard 0-10V dimming (100% to 10% range, minimum 150 A source current) Internal accessible driver tray compartment allowing field maintenance and driver replacement without full fixture disassembly or removal from mounting base Flush mounting base with vandal-resistant stainless steel fasteners; nominal overall dimensions of 36 inches height, approximately 14.25 inches width (at curved profile), and 6 inches base depth/footprint Wet locations listed (CSA/ANSI/UL 1598 and UL 8750 compliant), IP65 ingress protection rating for dust-tight and water-jet resistant performance Textured architectural powder coat finish over chromate conversion coating for enhanced corrosion resistance (standard bronze or black; custom colors allowable) Operating temperature range of at least -40°C to +50°C, with minimum 5-year warranty on components Designed for high-traffic outdoor applications including pedestrian pathways, parking areas, landscape accents, and site perimeter lighting Salient Technical Characteristics for the base: Heavy-duty die-cast aluminum adaptor plate (minimum thickness to ensure structural rigidity, typically 1/2 inch or greater) with corrosion-resistant finish suitable for outdoor/wet locations Universal slot pattern accommodating common existing anchor bolt configurations: 3-bolt at 120°, 4-bolt at 90°, or 2-bolt at 180° layouts; bolt circle diameters ranging from approximately 3.5 inches to 5 inches Slots sized to accept 1/4-inch to 3/8-inch diameter anchor bolts; includes provisions for large-diameter field-drilled holes to install new anchors if existing bolts are damaged or mismatched Integrated stainless steel leveling bolts (minimum 4) with built-in leveling bubbles (positioned at 90° orientations) for precise plumb alignment of the adaptor plate prior to bollard mounting Enables direct mounting of new bollard fixture to the adaptor plate without concrete demolition, anchor bolt extraction, or foundation modification, minimizing site disruption and labor Compatible with round and square/curved-profile bollard bases for retrofit to legacy or mismatched installations from various sources Vandal-resistant design suitable for high-traffic pedestrian and vehicle-adjacent areas No-demolition retrofit capability preserving existing concrete foundation integrity while allowing upgrade to modern LED bollards Fixtures and accessories shall meet or exceed all salient characteristics listed above without deviation. Or equal submissions must demonstrate compliance with every bullet point via submittals including cut sheets, photometric reports (IES files verifying Type III full-cutoff distribution and lumen output), and material certifications. No exceptions or alternates permitted unless pre-approved in writing. Salient Technical Characteristics for the Outdoor LED Bollard Interlocking die-cast, low-copper aluminum (<0.6% Cu) top and louver sections fastened together with concealed stainless steel screws for clean appearance and vandal resistance Louver design with full overlapping/interlocking arrangement providing total source cutoff above horizontal (zero uplight, full shielding of LEDs, low-brightness output with no direct view of light source) Extruded aluminum riser shaft, 5-inch diameter, minimum 0.125-inch wall thickness, with external vertical grooves aligning with vertical members on louver assembly for seamless aesthetic integration Riser attachment to anchor base using 4 countersunk stainless steel flat socket head screws Heavy cast aluminum anchor base fully concealed within the riser shaft, including rigid pressboard gasket/template and provisions for secure mounting Anchor hardware: Three 3/8-inch diameter x 10-inch length + 2-inch projection zinc-plated anchor bolts, each with two nuts, flat washers, and rigid nuts/washers for leveling and secure installation Optical system: Each LED equipped with individual directional optic for controlled beam angle projecting through louver stack spacings; LED boards mounted to anodized aluminum heat sink extrusions with inter-locking design LED configuration: 20 LEDs total (e.g., three 5-LED boards or equivalent multi-board arrangement for 20-diode setup), delivering medium-wide asymmetric distribution suitable for pedestrian pathways and site lighting IESNA light distribution: Type III (medium-wide forward throw, asymmetric pattern with extended forward reach, controlled side spill, minimal backlight, and soft transitions for uniform illumination without hotspots); available in other types (I, V) but specified here as Type III for pathway optimization Light throw pattern details: Broad, low-glare distribution achieved via louver-modulated optics; peak intensity forward with sharp horizontal cutoff; no uplight emission for dark-sky compliance; soft, glare-free illumination with high visibility at low mounting heights Internally fluted, clear tempered glass globe fully gasketed for protection and diffusion Electronic driver: Multi-level 0-10V dimming interface (dimming to low levels), quick-disconnect plugs, rated for -40°F starting temperature; universal voltage (typically 120-277V), low THD, high power factor Nominal height: 32 inches overall (centerline of light source approximately 26-28 inches above grade, with 2.5-inch minimum burial/grade adjustment) Nominal dimensions: 6-inch diameter/width at base and top, 8-inch maximum diameter at certain points per dimensional callouts Maximum weight: 20 lbs Finish: Electrostatically applied, thermally cured, abrasion-resistant TGIC polyester powder coat (e.g., white gloss smooth or matte textured; UV-stable, fade-resistant) Certifications: UL 1598 and UL 8750 listed (or equivalent), CSA wet locations compliant, RoHS compliant, meets Buy American provisions where applicable Operating temperature: Minimum -40°F starting capability; suitable for wet locations and high-traffic outdoor pedestrian/pathway applications Additional distinctive features: Concealed fasteners throughout exposed surfaces; rigid, vandal-resistant construction with no visible hardware; directional optics integrated with louver stack for controlled, low-brightness performance No-demolition retrofit capability preserving existing concrete foundation integrity while allowing upgrade to modern LED bollards Fixtures and accessories shall meet or exceed all salient characteristics listed above without deviation. Or equal submissions must demonstrate compliance with every bullet point via submittals including cut sheets, photometric reports (IES files verifying Type III full-cutoff distribution and lumen output), and material certifications. No exceptions or alternates permitted unless pre-approved in writing. This last bollard needs a bullet point for Drive Current (Type 1, 3, or 5), BUG Rating (Temperature of 3/4/5K Backlight, Uplight, and Glare (Type 1, 3, or 5), and Absolute Lumens 3/4/5K (Type 1, 3, or 5). In addition, provide and answer the following: 1. Company name, address, point(s) of contact, title, telephone number, fax number, email address, cage and SAM UEI number. 2. Company s business size, to include number of employees. 3. Company's socioeconomic status. 4. If SDVOSB/VOSB is planning to provide a response they need to demonstrate the ability to provide a product manufactured by a small business to be considered capable. Submit this information to Contracting Officer, Benjamin Amato, via email to
[email protected]. Your response to this notice must be received in writing on or before 1:00 PM (Eastern Standard Time) on February 3, 2026.